Re: Какой сетевой интерфейс используется при перемещении ВМ между хранилищами?
конечно устроит, вмошна то уже нет. а просветите, плз, что за data planer?
View ArticleClik here to view.
Re: ProfessionalVMware.com - BrownBag - VCP5 Series
Congratulation!! Great work..Regards,Milton
View ArticleRe: direct attached storage: interfaces not detected in vSphere Client
Hi- the SAS adapters are on the HCL, and I installed the vib package provided by dell (vmware-esxi5.0-SAS-provider.vib) using PuTTY I ran the command esxcli software vib list | grep LSI which appears...
View ArticleRe: Unable to select VMware Infrastructure Server
Not sure whether this is the root cause, but the screen shot shows the source disk with a capacity of 96GB and you only have a datastore with 65GB capacity!? André
View ArticleClik here to view.
Clik here to view.
unable to obtain hardware information for the selected machine
helloi tried to take image of my pc and i get this eror i attach the log file can anyone help me?
View ArticleRe: Какой сетевой интерфейс используется при перемещении ВМ между хранилищами?
urbas wrote: конечно устроит, вмошна то уже нет. а просветите, плз, что за data planer?Handles the packet switching functions. Вы не согласны со схемой когда нет общего хранилища у 2 хостов?
View ArticleClik here to view.
Re: Proof of concept setup
djak44 wrote: Dearl all, I will be installing a view 5 as a proof of concept for my client, because of many reasons I will be doing it in a developement environment, beside sharing some of the services...
View ArticleClik here to view.
Re: Update manger IP address issue
Hi, first of all, it shouldn't be a common problem, since using NAT between vCenter and ESXi hosts is an unsupported configuration by VMware How it should work anyway: In vSphere Client go to...
View ArticleRe: Какой сетевой интерфейс используется при перемещении ВМ между хранилищами?
Sladky wrote: Подтверждаю, данные с хоста на хост бегают без участия менеджмент сети. Но!!! Если у 2-х хостов нет доступа к чужим датасторам , то вот тут трафик побежит уже по менеджмент сети.Это...
View ArticleClik here to view.
Re: Move-HardDisk Format Change question
Hi, Yes, I'm moving a test machine form Datastore1 to Datastore2, the initial move from DataStore1 to DataStore2 I changed the disk format from Thick to EagerZeroedThick just moving back it refuses to...
View ArticleGetting two VMs to communicate
I am trying to learn how to use SCCM. I have two VMs on my laptop. One is Server 2008 R2 and i also have a Windows 7 VM. On the Server 2008 I have setup the domain controller, DNS, and DHCP. Now I...
View ArticleClik here to view.
Re: How to separate VDI servers and VMs on 2 VLANs ?
You have to route two VLAN for communicating between two VLAN. You can use cisco router for doing this. Here is a reference for configuration in cisco router....
View ArticleRe: vCenter Inventory Services
Ok let me try to explain:there are two passwords associated with the admin@system-domain.1) Master password: This is the password that you set while you first install SSO. This cannot be changed...
View ArticleAfter upgrading to 1.5 i cant login to administrate users etc
I can login to the Connector where i where all seems fine. Clicking on "Login in to Horizon" i get to fill in username and then password. It says signing in for 2 seconds and then nothing.. just an...
View ArticleRe: unable to obtain hardware information for the selected machine
Do you use local administrator account? Second: turn off UAC or run Converter client 'as administrator'. HTH
View ArticleRe: Horizon 1.5 change FQDN
I managed to both change certificates and external load balancer + FQDN. In my test i managed to do it in 2 ways. #1: Using the tip in this thread i used the fqdn i wanted as gateway-va name, then i...
View ArticleRe: Linux guest で動作している SAMBAへ Windows host から接続出来ません。
ご回答ありがとうございました。事情により，すぐには試すことができませんが，試行ができたらその後の状況をご報告します。
View ArticleRe: unable to obtain hardware information for the selected machine
Issues like this are often seen with UAC enabled and/or with running the Converter without the required permissions. Please try to start the Converter by right clicking and "Run as Administrator". If...
View ArticleRe: HOL Stucked at - starting lab
It looks like there might have been an issue earlier but at this point, I was able to start a lab. Thanks for your patience and please try again. Bill
View Article